Holly Hill, FL, in Volusia County
Holly Hill’s Small Garages and the Shops on Ridgewood
A small city on the Halifax River, tucked between Ormond Beach and Daytona Beach. Older houses on smaller lots, and a commercial strip along US-1 with floors of its own to deal with.
A small city between two bigger ones
Holly Hill is easy to drive through without noticing where it starts. It sits on the Halifax River with Ormond Beach to the north and Daytona Beach to the south, a small city in a stretch of Volusia County full of bigger names. Most of the houses are older, and most of the lots are on the smaller side.
Older houses mean older slabs, and older slabs have a history. A garage floor here might have been painted twice, patched where a crack opened up and stained by a car that leaked oil for years. Some have settled. Florida’s humidity and high water table keep pushing moisture up through the concrete the whole time, and moisture under old paint is exactly why so many painted garage floors end up peeling.
Then there is US-1, which runs through town as Ridgewood Avenue and carries most of the businesses. Commercial floors there take a different kind of beating: customers walking in off the street, carts, equipment, now and then a vehicle. They also have to be done around business hours, which makes planning half the job. Holly Hill is at the southern edge of what we cover from St. Augustine, so Matt confirms each job there before it goes on the calendar.
When the garage is also the laundry room and the workshop
On a smaller lot the garage pulls more than one shift. It holds the car, and also the washer and dryer, the workbench, the chest freezer and every tool in the house. People in older homes ask for a floor that cleans up easily and stops looking like a garage when the door is open. Some ask about the inside of the house too, usually after old carpet or tile comes up and leaves bare concrete behind.
Along Ridgewood Avenue the questions come from business owners: a showroom that has to look clean, a service bay that takes oil and dropped tools, a back room that gets hosed down at closing. A storefront floor and a shop floor carry very different loads, so each one gets its own system, matched to what it deals with every day.
People in older homes ask for a floor that cleans up easily and stops looking like a garage when the door is open.
Floors for a working garage and a storefront
What Matt reaches for most on Holly Hill slabs, and why. See all of Matt’s floors.
A garage that doubles as laundry room and workshop needs a ground, primed slab and a tough topcoat that wipes up detergent spills and shrugs off a dropped wrench.
When old carpet or tile comes up in an older home, the bare slab can be finished in a solid color or decorative epoxy instead of covered over again.
Storefronts and offices along Ridgewood Avenue get a system built for steady foot traffic, scheduled around the hours the doors are open.
A service bay takes oil, brake fluid and dropped parts. A solid-color shop floor shows what fell, cleans up fast and holds up under a vehicle lift.
For a retail floor that should look sharp with no coating on top, polishing the concrete itself gives a hard, bright surface that is simple to keep clean.
Matt’s first look at an older Holly Hill slab
Start with a phone call. Holly Hill is in Volusia County, at the far southern end of our range, and Matt checks each job down there before he says yes. Tell him whether it is a house or a business, which floors you want done and about how big they are, and he will tell you straight whether it fits the schedule. Business owners should mention how long the floor can be out of service.
On the visit, older slabs get extra attention. Matt tests for moisture, looks for layers of paint and sealer, checks whether cracks are still moving and asks what the floor deals with day to day. Then he tells you what the prep involves and which system fits. Many garage floors finish in one day. Call Matt at (904) 671-3930.
Or email spartancoatingsfl@gmail.com with the town and a photo of the floor.
Matt answers this phone himself
Based in St. Augustine, FL, working in Holly Hill.
Finished floors first? See all of Matt’s floors.
Other Volusia County towns on our route
A narrow, mostly residential strip on A1A between the Atlantic and the Halifax River, where salt air and blowing sand reach every porch, pool deck and garage, so outdoor slabs need sound edges and a UV-stable topcoat.
Large subdivisions full of garages and pool decks along the Halifax River, with Spruce Creek next door, a fly-in community where a home’s hangar floor has to carry an airplane and the tools that come with it.
Split by the Halifax River, with older beachside homes whose slabs often carry old paint and salt-worn edges east of the river, and newer subdivisions west of I-95 where moisture testing on younger concrete matters most.
The inland county seat near the St. Johns River, home to Stetson University, where older homes around the historic downtown and newer subdivisions alike start with a moisture test, because humid summers push water up through the slab.
Home of Daytona International Speedway, with beachside condos and hotels, mainland neighborhoods and plenty of auto and motorsport shops whose floors have to take oil, fluids, hot tires and vehicle lifts.
Everything in the county: Volusia County.
Questions from Holly Hill
Our garage floor was painted years ago and it’s peeling. Can you coat right over it?
We never coat over peeling paint. It is already letting go, and it would take the new floor down with it. The paint gets diamond-ground off to clean concrete, cracks and chips get repaired and the slab gets a moisture test. If moisture is what lifted the paint in the first place, a vapor barrier primer goes down before the rest of the system.
The washer and dryer live in our garage. Do they have to come out?
Yes. Everything comes off the floor, washer, dryer, freezer and workbench included, so we can grind and coat the whole slab in one piece. Coating around appliances leaves raw edges that peel later. Plan where those things will sit during the job and how long the floor needs before heavy items go back on. Matt gives you that timing at the visit.
Can a business on Ridgewood Avenue stay open while the floor gets done?
Usually not in the area being coated. Grinding is loud and dusty, and a fresh coating needs time before anyone walks on it. Many businesses schedule the work around a closed day or split the floor into sections done on different days. Matt will ask about your hours and plan the job around them before anything is booked.
There’s an old crack across our slab. Will it show back up through the coating?
That depends on whether the crack is still moving. We grind it out and fill it with a repair material before coating, which takes care of most cracks in older slabs. If a crack is active because the slab is still settling, it can work its way back through any coating over time. Matt checks for that and tells you what to expect up front.
We’re pulling up old tile inside. Can the slab underneath be coated?
Yes, once the tile and its adhesive are fully off. Thinset and glue left behind get ground away to bare concrete, then the slab is tested, repaired and coated. Some floors come out of a tile removal with patches and holes, and those get filled first. Solid color, flake or metallic all work inside, depending on the look you want.